140-ton 10-foot Hydraulic Press Brake

ed in the People's Republic of China (or any other non-qualifying, non-TAA compliant country) is SPECIFICALLY EXCLUDED from consideration and will be evaluated as TECHNICALLY UNACCEPTABLE. Can you provide more details on the electrical run. Conduit type, for instance. Will it be overhead or along a wall? Is a scissor lift required for electrical install? In the RFQ, it stated that the government would wire to a disconnect and only the final connections would need to be made. The additional information provided, seems to contradict the RFQ by stating that the electrical would be run from the main panel? Conduit is in the floor, installation electrician is on site, electrical panel is 35-40 ft away. Does the electrician need special certifications to work onsite? Installation electrician is on site Also, for the riggers, do they need special certifications to work onsite?� They will need a Real ID to get on base. Electrical Connection: Further clarification is needed. Please confirm that the Government/end user will provide the electrical drop, disconnect, and required electrical connection so that the machine can be connected and placed into service at installation. By law, the manufacturer or rigging contractor cannot perform electrical wiring. Installation Electrician will be on site to connect power Facility Access: Please advise what credentials or forms of identification will be required for the freight carrier, rigging crew, manufacturer�s technician, and/or trainer to enter the facility. Real ID is required along with an EAL Offloading Equipment: Is there an onsite forklift of sufficient capacity available for use in offloading and positioning the machine, or should the rigging contractor provide all required forklift/crane equipment? Yes Startup/Test Bend: The solicitation requires a live test bend using Government-furnished material. Please confirm that the Government will have the appropriate material available onsite at the time of startup/commissioning and training. Yes, we will have material on-site Final Machine Placement: Please confirm that the final machine placement area is a flat, level concrete surface suitable for installation and anchoring of the approximately 14,000�16,000 lb press brake. Yes IUID: Please confirm if an IUID is required for this purchase. Yes End Amendment 4 Amendment 3 The purpose of this amendment is provide answers to questions that have been received up to 9/8/2026. Category 1: Tooling & Material Specifications Material Types & Thickness: What are all the material thicknesses you intend to form (from thinnest to thickest)? What are the specific types and grades of material you will be working with (e.g., A36 Mild Steel, 5052 Aluminum, 304 Stainless Steel)? 321 Stainless Steel 0.016 � 0.180 302 Stainless Steel 0.016 � 0.180 4901 Titanium 0.020 � 0.120 9046 Titanium 0.020 � 0.120 2024-T3 Aluminum 0.016 � 0.125 2024-T81 Aluminum 0.016 � 0.125 7075-O Aluminum 0.030 � 0.160 7075-T6 Aluminum 0.030 � 0.160 6061-O Aluminum Up To 0.125 (No other sizes are listed in our inventory) 7075-T651 Up to 0.250 (No other sizes are listed in our inventory) 5052-H43 0.020 � 0.375 Mild Steel 0.020 � 0.250 Tooling Configuration: For each material type and thickness, what is the required tooling configuration?. What are the required V-opening sizes for the Multi-V Bottom Die? Please provide specifics. Selecting the correct V-opening (V) depends heavily on your material thickness (T) and type. Mild Steel: formula: V = 8 � T Stainless Steel (Harder): typically V = 10 � T or 12 � T Aluminum (Softer): Often uses V = 6 � T for soft grades, or up to 10 � T - 12 � T for hard/T6 grades to prevent surface cracking. What are the required punch dimensions and angles for the Gooseneck Punch? Tip Working Angle: Ranges from 30�, 45�, 60�, 85�, 88�, to 90�. Springback Target Angle: Usually 88� or 86� for air-bending standard 90� parts. Outward Neck Angle: Ranges between 42� and 45� to provide relief clearance. Clamping Method: The solicitation specifies "quick-release clamping." Please clarify the preferred method: a) Hydraulic Clamping Category 2: Machine Configuration & CNC System CNC Gauging Axes: What is the required number of CNC gauging axes? CNC Control: 2-axis to 5-axis CNC with programmable sequences for repeatable bends Is there a specific back gauge configuration required? Back Gauge: Programmable back gauge for precise material positioning. Back Gauge Length: 23.6 � 25.6 in. Back Gauge Motor: � hp Category 3: Facility, Installation & Rigging Installation Location: What is the building number and exact installation location for the press brake? Bldg 80 Aircraft Structural Maintenance shop Please confirm if "Building 60" is the final installation site or only the ship-to/receiving address. Only the ship-to/receiving address. Rigging & Placement Path: Can you provide photos or drawings of the entire delivery and rigging path? This should include: Exterior access points to the building. 12x12 ft Exterior overhead door / 2 ft grade Dimensions of overhead doors and interior doors/openings. 10x10 ft interior overhead door / 1ft grade Any changes in floor elevation or steps. No The total distance from the unloading point to the final placement spot. 100 yards Any overhead clearance or width restrictions along the path. No Category 4: Electrical & Power Requirements Power Connection: Will the facility provide the final power disconnect box near the press brake, or does this need to be included in the vendor's scope of work? If the vendor is to quote the connection, please provide: Details on the available power at the main electrical panel. 40A 208V 3 phase or 30A � 40A 480V 3 phase The distance of the electrical run from the main panel to the press brake's location. 35-40 feet Photos of the main electrical panel and the proposed path for the electrical run. Path is already existing to another piece of equipment Category 5: General & Administrative Physical Constraints: Is the 156" (13-foot) maximum length/space constraint firm? One vendor (Accurpress) notes that their machine may fit, but the electrical cabinet door and optional safety systems could interfere with this limit. Please confirm if any flexibility is possible. 12-foot outside overhead door to bring the machine into the shop. 10-foot interior overhead door from the hangar. End Amendment 3 Amendment 2 The purpose of this amendment is to update the solicitation document to remove a manufacturer part number. This is a generic solicitation and not brand name or specfic to any brand/manufacturer. End Amendment 2 Amendment 1 The purpose of this amendment is to update the description language and add in information necessary for potential quoters. End Amendment 1 Solicitation Number: W50S7L-26-Q-A004 This is a combined synopsis/solicitation for commercial products or commercial services prepared in accordance with the format in FAR Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; quotes are being requested and a written solicitation will not be issued. This solicitation is issued as a Request for Quotation (RFQ) under solicitation number W50S7L-26-Q-A004. The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular (FAC) 2026-01. This requirement is a 1