Classified Sound-Attenuated Door and Split-Frame Assembly Package

ication. All other terms and conditions remain unchanged. Question 1: Does the SBA Nonmanufacturer Rule apply to this acquisition, including FAR 52.219-33 or another applicable NMR provision? Answer 1: The solicitation identifies this acquisition as a Commercial Supply / Direct Purchase, Supply-Only, No Installation, and includes FAR 52.219-6, Notice of Total Small Business Set-Aside. However, FAR 52.219-33, Nonmanufacturer Rule was not included to the solicitation. Question 2: Is an SBA class or individual waiver applicable to the required end items? Answer 2: The solicitation does not identify any SBA class waiver or individual waiver applicable to the required end items, and FAR 52.219-33, Nonmanufacturer Rule, was not included in the solicitation. Due to the limited time remaining in FY 2026, requesting or processing an individual SBA waiver at this stage would likely delay award and may adversely impact the mission requirement. Therefore, absent identification of an existing applicable SBA class waiver, the acquisition should proceed in accordance with the solicitation�s current terms and conditions and applicable small business set-aside requirements. Any offeror seeking to rely on a waiver should provide the specific waiver citation or documentation immediately for Contracting Officer review. Question 3: If no waiver applies, must the actual end-item manufacturer qualify as a small business under the assigned manufacturing NAICS code? Answer 3: Generally, yes. If the Nonmanufacturer Rule applies and no SBA waiver or other exception applies, the small business prime/dealer must provide the end item of a small business manufacturer or processor. The manufactured end item must also be made in the United States, consistent with the NMR requirements and the solicitation�s domestic sourcing clauses. Question 4: May a small-business prime/dealer furnish an otherwise fully compliant commercial product manufactured by a large business? Answer 4: Generally, no, if the Nonmanufacturer Rule applies and no SBA waiver or exception is available. Under the NMR, a small business prime/dealer normally may not furnish the product of a large business manufacturer for a small business set-aside supply acquisition unless an SBA waiver or other applicable exception permits it. The solicitation also includes FAR 52.225-1, Buy American-Supplies, and FAR 52.225-18, Place of Manufacture, so country of origin and place of manufacture must also be addressed in the quote. Question 5: Please confirm the complete six-digit NAICS code and size standard controlling this procurement if different from the abbreviated NAICS shown in the public notice. Answer 5: NAICS: 561622, Locksmiths Clarification: The correct solicitation number is 70LGLY26Q00000056, not 70LGLY26Q00000060. This correction applies throughout the entire solicitation document. **************************************************** 9/18/2026 Subject: Amendment 0002, Questions and Answers Amendment 0002 The purpose of this amendment is to provide the Government�s responses to questions received regarding the type of wood. All other terms and conditions remain unchanged. Question1: Would an alternate high-security hollow metal door (HMD) be acceptable for this requirement? Answer 1: Yes. A high-security hollow metal door (HMD) is acceptable, provided it meets all solicitation requirements, including the STC 50 acoustic rating and the complete split frame and hardware package requirements. *************************************************************************************** 9/18/2026 Subject: Amendment 0001, Questions and Answers Amendment 0001 The purpose of this amendment is to provide the Government�s responses to questions received regarding the lockset and cylinder requirements. All other terms and conditions remain unchanged. Question 1: The solicitation states: �Factory-installed lockset prepped for Schlage interchangeable core.� Please clarify the specific lockset hardware required. Is the required lockset a LockOne LKM10K Lock Series? Answer 1: Confirmed. The requirement is for a factory-installed lockset. The lockset shall be a LockOne LKM10K Lock Series. Question 2: The solicitation states: �Schlage 20-079 626 cylinder, or approved equivalent.� Please clarify the specific cylinder/core requirement. Answer 2: The requirement is for a factory-installed Schlage 20-079 626 cylinder. The Government will provide the small format lock cylinder/core. *************************************************************************************** 1.0 Combined Synopsis / Solicitation Statement (FAR 12.202(b)(1)(i)) This is a combined synopsis/solicitation for commercial products prepared in accordance with the format in Federal Acquisition Regulation (FAR) Subpart 12.202, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; offers/quotes are being requested and a separate written solicitation will not be issued. Solicitation Identification: Solicitation number 70LGLY26Q00000056 is issued as a Request for Quotation (RFQ) for the procurement of a Classified Sound-Attenuated Door and Split-Frame Assembly Package for Room 8 at the Federal Law Enforcement Training Centers (FLETC), Glynco, GA. Small Business Set-Aside Status: This acquisition is 100% Total Small Business Set-Aside under NAICS code 561622. PSC: 5670 Provisions and Clauses: This solicitation incorporates provisions and clauses by reference and in full text. The full text of provisions and clauses may be accessed electronically at: Federal Acquisition Regulation (FAR): https://www.acquisition.gov/ Homeland Security Acquisition Regulation (HSAR): https://www.acquisition.gov/hsar Defense Priorities and Allocations System (DPAS): DPAS rating is not assigned to this commercial requirement 2.0 Contract Schedule of Supplies (CLIN Structure) (FAR 12.202(b)(1)(ii)) The Government contemplates the award of a single Firm-Fixed-Price (FFP) Commercial Purchase Order resulting from this RFQ. CLIN: 00001 Description: STC 50 Sound-Attenuated Wood Door, Split Frame & Complete Hardware Package Quantity: 1.0 Unit of Issue: LOT Unit Price: Total Firm-Fixed-Price Pricing Terms & Tax Status: All-Inclusive Firm-Fixed-Price: Quoted pricing for CLIN 0001 is all-inclusive. All crating, in-transit insurance, freight transportation (FOB Destination), delivery, and hardware components must be included in the lump-sum price. Tax Exemption: The United States Federal Government is tax-exempt. No state, local, or sales taxes shall be applied. 3.0 Description of Requirement & Salient Characteristics (FAR 12.202(b)(1)(iii)) 3.1 Scope of Requirement This acquisition is strictly for the factory manufacture, hardware integration/preparation, protective crating, and delivery (FOB Destination) of one (1) factory-engineered, high-performance sound-attenuated wood door and split-frame assembly package. The door assembly must achieve an independently certified laboratory sound rating of Sound Transmission Class (STC) 50 or higher to satisfy federal standards for classified and secure discussion spaces (Secure Compartmented Information Facility [SCIF] / Secure Working Area [SWA] standards). Note: This contract is for supply-only delivery. Field installation, on-site wall integration, and perimeter drywall work are excluded. 3.2 Salient Physical, Func