ARMING UNIT, ELECTROMECHANICAL

ND ACCEPTANCE AT ORIGIN RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES RT001: MEASURING AND TEST EQUIPMENT __________ RQ032: EXPORT CONTROL OF TECHNICAL DATA This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. __________ THIS ITEM IS A "DEFENSE ARTICLE" AS DEFINED IN AND SUBJECT TO THE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS (22 C.F.R. 120-30) AND THE ARMS EXPORT CONTROL ACT (22 U.S.C.A. 2778-2799). ANY MANUFACTURER OR EXPORTER OF DEFENSE ARTICLES IS REQUIRED TO REGISTER WITH THE DIRECTORATE OF DEFENSE TRADE CONTROLS (DDTC), DEPARTMENT OF STATE. DOCUMENTARY EVIDENCE OF REGISTRATION MAY BE REQUIRED PRIOR TO AWARD. ADDITIONAL EXPORT RESTRICTIONS APPLY AS INDICATED HEREIN. FAILURE TO SUBMIT DDTC REGISTRATION WHEN REQUESTED WILL MAKE A QUOTE/OFFER INELIGIBLE FOR AWARD. __________ The Government Procuring Activity has determined that Surplus is not Acceptable for this NSN. (End of TQ Requirement) _______________EXCEPTION DATA____________________ DRAWING 200415485 ONLY NOTES 1,3,4,10,11, AND 12 APPLY ______________END OF EXCEPTIONS__________________ THE ITEM BEING PROCURED IS A CRITICAL GUN PART ITEM WITH UNIQUE REQUIREMENTS. GOVERNMENT FAT APPLIES. AFTER RECEIPT OF QUOTES, OFFERORS MAY BE CONTACTED TO PRICE THE FAT REQUIREMENT. TWO (2) EXHIBITS ARE REQUIRED: ONE (1) ASSEMBLED COATING AND ONE (1) MACHINED BUT NOT ASSEMBLED AND WITHOUT COATING. EXHIBIT DISPOSITION INSTRUCTIONS: ONE (1) PART WILL Page6 /10 BE RETURNED TO THE CONTRACTOR AND CAN BE INCLUDED IN THE PRODUCTION QUANTITY. ONE (1) WILL BE DAMAGED IN TESTING. PRODUCT INSPECTION WILL BE CONDUCTED BY THE DCMA QAR AT THE ACTUAL MANUFACTURER'S FACILITY. THE IDENTIFICATION OF THE ACTUAL MANUFACTURER MUST BE SUBMITTED TO THE CONTRACTING OFFICER FOR INCLUSION IN THE AWARD. UPON AWARD, ANY CHANGES TO THE ABOVE MUST BE APPROVED BY THE PCO VIA FORMAL CONTRACT MODIFICATION. PRODUCT VERIFICATION TESTING (PVT) IN ACCORDANCE WITH PROCUREMENT NOTE E05, MAY BE INVOKED FOR THE REFERENCED CONTRACT. IF INVOKED, PVT SAMPLES MUST BE INSPECTED, PACKAGED AND MARKED AS REQUIRED IN THE CONTRACT. ONE (1) SAMPLE MAY BE DESTROYED DURING TESTING. PRODUCT VERIFICATION TESTING, IF INVOKED<(>,<)> WILL BE PERFORMED PRIOR TO ACCEPTANCE OF EACH SHIPMENT. THE CONTRACTOR MUST PROVIDE PVT SAMPLES FROM EACH (SUB)CONTRACTOR USED IN THE PRODUCTION OF PARTS ON THIS CONTRACT. FIVE (5) PVT SAMPLES, UNLESS OTHERWISE SPECIFIED, WILL BE REQUIRED TO BE IDENTIFIED TO THOSE (SUB)CONTRACTORS WHEN THEY ARE SENT IN FOR TESTING. CERTIFICATE OF CONFORMANCE IS NOT AUTHORIZED. __________ CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS. ____ WHEN FIRST ARTICLE IS REQUIRED IN THE CONTRACT, THE CONTRACTOR SHALL MARK THE OUTER SHIPPING CONTAINER IN 2 INCH BOLD, RED LETTERS "FIRST ARTICLE". THE CONTRACTOR SHALL ALSO PROVIDE THE TESTING FACILITY WRITTEN NOTIFICATION OF WHEN THE FIRST ARTICLES EXHIBITS WILL BE SHIPPED TWO WEEKS BEFORE THE SHIP DATE. CRITICAL APPLICATION ITEM IAW BASIC DRAWING NR 98752 7631354 REVISION NR L DTD 01/11/2005 PART PIECE NUMBER: 7631354-10 IAW REFERENCE DRAWING NR 98752 7842728 REVISION NR K DTD 10/25/2015 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98752 200415485 REVISION NR E DTD 01/30/2020 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98747 65B12054 REVISION NR E DTD 11/03/1983 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98747 65B12055 REVISION NR D DTD 07/12/2019 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 18894 65C12057 REVISION NR F DTD 09/04/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 18894 65B11917 REVISION NR C DTD 11/14/1972 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 18894 65C12057-07A1004 REVISION NR F DTD 08/05/2007 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98747 65B12054-72662 REVISION NR C DTD 03/23/1972 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98747 65B12054-83A304 REVISION NR E DTD 11/23/1983 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98747 65B12054-91A001 REVISION NR E DTD 12/12/1990 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98747 65B12055-72663 REVISION NR C DTD 03/22/1972 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98747 65B12055-91A212 REVISION NR D DTD 08/14/1991 PART PIECE NUMBER: Page8 /10 IAW REFERENCE DRAWING NR 98747 65B12055-94A078 REVISION NR E DTD 06/23/1994 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98747 7227131-79A043 REVISION NR B DTD 01/05/1979 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98747 7227131-91A005 REVISION NR B DTD 01/05/1991 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98747 7227131-91A248 REVISION NR B DTD 08/15/1991 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98747 65B11917-72759 REVISION NR C DTD 11/20/1972 PART PIECE NUMBER: IAW REFERENCE QAP 16236 SQAP010526055 REVISION NR A DTD 02/28/2017 PART PIECE NUMBER: IAW REFERENCE DRAWING NR 98747 7227131 REVISION NR B DTD 01/01/1939 PART PIECE NUMBER: