KB Duct List
Army Mission and Installation Contracting Command (MICC) · W6QM MICC-FT DRUM
Capture briefs (a one-page, shareable copy of this page) are part of Pro. The CSV here holds the notice, its timeline and past awards.
Where this opportunity stands
Every notice posted under solicitation W911S226U4569 in this department, oldest first.
- Sep 30, 2026 · this noticeCombined Synopsis/Solicitation
Next steps for this stage
Standard steps for the notice type; not advice about this buyer.
- Decide bid or no bid before the response deadline.
- Look at the past winners for likely competitors and teaming partners.
- Follow the opportunity to hear about amendments and the award.
What the notice says
Salient Characteristics SpecificationTitle: Galvanized Steel Quick-Disconnect Ductwork and Components for Air-Conditioning SystemSubject: Supply of modular galvanized steel quick-disconnect ductwork, fittings, dampers, and support hangers.Basis of Design: The part numbers below are for reference and configuration cross-reference. Products offered may be from another acceptable manufacturer, provided they meet or exceed all salient characteristics and are fully compatible with the complete ductwork system.1. Scope and PurposeThis requirement is for the supply and delivery only of galvanized ste… (show all)
el, modular quick-disconnect ductwork and associated fittings for an air-conditioning system. The supplied components shall form a mutually compatible duct system consisting of straight duct sections, reducers, wye connectors, elbows, airflow dampers, and saddle hangers.Installation, field fabrication, field welding, and connection to existing equipment are not included unless specifically added elsewhere in the solicitation.2. General Salient Characteristics. All offered items shall meet the following minimum requirements: Material: Items 1 through 26 shall be galvanized steel only. No stainless steel, aluminum, plastic, or uncoated carbon-steel substitutes shall be accepted.System Compatibility: All duct, fittings, dampers, and hangers shall be compatible with the specified quick-disconnect duct system. Components of the same nominal duct diameter shall connect directly without adapters, field welding, rivets, sheet-metal screws, or permanent field modification.Quick-Disconnect Connection: Straight duct sections, reducers, wye connectors, elbows, tees, and dampers shall use a quick-disconnect connection configuration compatible with the remaining supplied components. Connection features shall permit assembly and disassembly of the duct system without damage to the duct or fittings.Nominal Dimensions: Duct diameters and fitting dimensions listed in the schedule are nominal inside diameters unless the manufacturer???s standard quick-disconnect system identifies dimensions differently. Reducers shall transition between the listed inlet and outlet diameters. Fittings shall be sized to directly mate with the corresponding duct diameter.Gauge Requirements: Straight duct sections and dampers shall be 20-gauge galvanized steel where identified in the schedule. Reducers, elbows, wye connectors, tees, and 90-degree fittings shall be 18-gauge galvanized steel where identified in the schedule. Saddle hangers shall be 14-gauge galvanized steel where identified in the schedule.Quality and Condition: Products shall be new, free of corrosion, dents, sharp edges, cracks, deformation, damaged coating, or manufacturing defects that would prevent proper assembly or service. Duct sections shall be round, and fittings shall retain their intended shape to allow proper connection. Components shall be packaged and shipped to prevent damage or distortion in transit.Equal Products: An offered equal product shall meet every listed dimensional material, gauge, connection, configuration, and quantity requirement. The offeror shall provide manufacturer specifications or product literature sufficient to verify compliance when requested.3. Required Items ScheduleItem. Required Item / Salient Characteristics. Minimum Material / Gauge. Qty. Reference No.*1. Quick-disconnect straight duct, nominal 24-inch diameter. Galvanized steel, 20 ga 17 EA 10024.2. Quick-disconnect reducer, 24-inch inlet to 22-inch outlet Galvanized steel, 18 ga 5 EA 16024.3. Quick-disconnect straight duct, nominal 22-inch diameter Galvanized steel, 20 ga 20 EA 10022.4. Quick-disconnect reducer, 22-inch inlet to 20-inch outlet Galvanized steel, 18 ga 5 EA 16022.5. Quick-disconnect straight duct, nominal 20-inch diameter Galvanized steel, 20 ga 17 EA 10020.6. Quick-disconnect reducer, 20-inch inlet to 18-inch outlet Galvanized steel, 18 ga 5 EA 16020.7. Quick-disconnect 45-degree wye connector, nominal 24-inch duct size Galvanized steel, 18 ga 1 EA 14224.45.8. Quick-disconnect 45-degree elbow, nominal 22-inch duct size Galvanized steel, 18 ga 1 EA 12022.45.9. Quick-disconnect manual butterfly valve airflow damper, nominal 22-inch duct size Galvanized steel, 20 ga 1 EA 19422.10. Quick-disconnect straight duct, nominal 18-inch diameter Galvanized steel, 20 ga 28 EA 10018.11. Quick-disconnect tee, 18-inch ?? 18-inch ?? 18-inch Galvanized steel, 18 ga 1 EA 14318.12. Quick-disconnect straight duct, nominal 16-inch diameter Galvanized steel, 20 ga 19 EA 10016.13. Quick-disconnect reducer, 18-inch inlet to 16-inch outlet Galvanized steel, 18 ga 3 EA 16018.14. Quick-disconnect 45-degree elbow, nominal 16-inch duct size Galvanized steel, 18 ga 2 EA 12016.45.15. Quick-disconnect manual butterfly valve airflow damper, nominal 16-inch duct size Galvanized steel, 20 ga 2 EA 19416.16. Quick-disconnect 90-degree elbow, nominal 20-inch duct size Galvanized steel, 18 ga 2 EA 12020.90.17. Saddle hanger sized for nominal 24-inch duct Galvanized steel, 14 ga 14 EA 17024.18. Saddle hanger sized for nominal 22-inch duct Galvanized steel, 14 ga 14 EA 17022.19. Saddle hanger sized for nominal 20-inch duct Galvanized steel, 14 ga 14 EA 17020.22. 16-inch galvanized clamp with white nitrile gasket, 27 EA 13016-GA-N.23. 18-inch galvanized clamp with white nitrile gasket, 30 EA 13018-GA-N.24. 20-inch galvanized clamp with white nitrile gasket, 25 EA 13020-GA-N.25. 22-inch galvanized clamp with white nitrile gasket, 28 EA 13022-GA-N.26. 24-inch galvanized clamp with white nitrile gasket, 24 EA 13024-GA-N.*Reference numbers are not brand-name requirements and are included only to identify the intended configuration and compatibility standard. Galvanized Ducting shall be Standard 5-feet Lengths and 11-inch Galvanized Standard Adjustable Sleeves where applicable.4. Component-Specific Requirements shall be galvanized steel:4.1 Saddle Hangers (items 17-21) used for handing duct systems and reducing sway Shall be nominal 24-inch diameter 14 ga 14 EA 17024, 22-inch diameter 14 ga 14 EA 17022, 20-inch diameter 14 ga 14 EA 17020, 18-inch diameter 14 ga 18 EA 17018, or 16-inch diameter 14 ga 14 EA 17016, as identified in the item schedule. Shall use the required quick-disconnect end configuration.4.2 Reducers Shall be galvanized steel, 18 gauge. Shall provide the listed nominal transitions: 24 x 22 inches, 22 x 20 inches, 20 x 18 inches, and 18 x 16 inches. Shall have quick-disconnect ends compatible with the adjoining duct sections.4.3 Elbows, Wye Connector, and Tee, shall be galvanized steel, 18 gauge. Shall have the listed nominal diameter and directional configuration. The wye connector and applicable elbows shall be 45 degrees as listed. The 20-inch elbow shall be 90 degrees. The tee shall be 18 inches ?? 18 inches ?? 18 inches. All ends shall be compatible with the required quick-disconnect duct system.4.4 Airflow Dampers Shall be galvanized steel, 20 gauge. Shall be sized for 22-inch or 16-inch nominal quick-disconnect duct, as identified in the item schedule. Shall be suitable for controlling airflow within the compatible duct system. 4.5 Saddle Hangers Shall be galvanized steel, 14 gauge. Shall be contoured and sized to support the corresponding nominal duct diameter without crushing, deforming, or damaging the duct. Shall be suitable for attachment to the Government???s selected overhead support method. 5. Inspection and Acceptance the Government may inspect delivered items for: Correct item type, nominal size, gauge, and quantity; Galvanized-steel construction; Compatibility of quick-disconnect connections among offered components; Required elbow, wye, tee, reducer, damper, and hanger configurations; Damage, deformation, corrosion, or deficient protective packaging; and Manufacturer literature or other documentation supporting compliance with the salient characteristics. Items that do not meet the stated requirements may be rejected.
Who won similar work
7 award notices on SAM.gov in the last 24 months. Match: Same agency (Army Mission and Installation Contracting Command (MICC)), same industry group (NAICS 3323).
| Winner | Awards | Value | Last |
|---|---|---|---|
| YOSWAY MARK P Estero FL 33928 USA | 2 | $83K | Jun 3, 2025 |
| TAZA SUPPLIES INC | 1 | $140K | Jun 10, 2025 |
| ALTERNATIVE LOGISTICS LLC | 1 | $32K | Sep 9, 2025 |
| UNITY CABLE TECHNOLOGIES INC | 1 | $29K | Mar 3, 2025 |
| Suncore Distribution LLC | 1 | $29K | Aug 21, 2025 |
| BHAYANA BROTHERS LLC | 1 | $22K | Apr 7, 2025 |
Value counts single-winner awards. "Shared" awards are multiple-award contracts that list every winner with the same total ceiling; that ceiling is not one company's win, so it is not added in.
- Sep 9, 2025ALTERNATIVE LOGISTICS LLC$32KMaintenance Stand
- Aug 21, 2025Suncore Distribution LLC$29KStorage Shelters
- Jun 10, 2025TAZA SUPPLIES INC$140KChain Hoist
- Jun 3, 2025YOSWAY MARK P Estero FL 33928 USA$42KDUMPSTERS FORT BRAGG
- May 7, 2025YOSWAY MARK P Estero FL 33928 USA$41KDUMPSTERS
- Apr 7, 2025BHAYANA BROTHERS LLC$22K18 ftx13 ft Duracoil Rolling Steel Door
- Mar 3, 2025UNITY CABLE TECHNOLOGIES INC$29KStorage Shelters
Competitive landscape
For the 6 most frequent past winners above. Lobbying is matched by the company's exact name or exact ticker; agencies are as named on the filings.
- 0 of these past winners lobbied Army, Dept of (Corps of Engineers) or Army, Dept of (Other) or Natl Guard since 2024 (0 filings)
- 0 of their lobbyists list a past Army, Dept of (Corps of Engineers) or Army, Dept of (Other) or Natl Guard job
- No corporate PAC money from them to the overseeing committees since 2024
- 0 foreign-agent (FARA) registrations
Policy around it
Bills the past winners named while lobbying this agency's issues, rules from the department, and executive orders that name the agency, last 12 months.
- 0 bills named on the past winners' lobbying filings
- 32 rules from the department in the last 12 months
- 0 executive orders naming the agency in the last 12 months
Market
For past winners matched exactly to a listed company. Insider trades are open-market buys and sells (Form 4) in the last 90 days, shown as facts; our own study found insiders do not reliably buy ahead of awards.
- 0 of the past winners are listed companies
- 0 insider buys and 0 insider sells at them in the last 90 days
Sources: SAM.gov notices and award notices; Senate LDA lobbying filings; FEC filings; FARA; Federal Register; congress.gov; SEC Form 4. Every row above links to its record.
Companies are matched to tickers by exact name only. A company we could not match shows no market rows; that is a miss, not a finding.