HOSE ASSY, A/C, #10

TION (3-18))|1|| NOTICE OF TOTAL SMALL BUSINESS SET-ASIDE (OCT 2020)(DEVIATION 2020-O0008)|1|| ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (OCT 2025)|13|||||||||||||| ANNUAL REPRESENTATIONS AND CERTIFICATIONS (MAR 2025)(DEVIATION 2025-O0003 AND2025-O0004))|13|332919|750|||||||||||| NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PERPARDENESS, AND ENRGY PROGAM USE (APRIL 2008))|2||X| NOTE: Award will be based on the toal for both items, not individual items. NOTE: THese are shelf life items (Y UU). Please ensure your material can meet this prior to quoting. TO VIEW THE DRAWINGS: Go to www.sam.gov Click: Contract Opportunities and enter the solicitation number. This gives access to the Electronic Solicitation. Drawings can be viewed or downloaded. GOVERNMENT SOURCE INSPECTION per FAR 52.246-2 IS REQUIRED. DELIVERY 90 DAYS. All contractual documents (i.e. contracts, purchase orders, task orders,delivery orders and modifications) related to the instant procurement areconsidered to be "issued" by the Government when copies are either depositedin the mail, transmitted by facsimile, or sent by other electronic commercemethods, such as email. The Government's acceptance of the contractor'sproposal constitutes bilateral agreement to "issue" contractual documents as detailed herein. \ 1. SCOPE 1.1 This contract/purchase order contains the requirements for manufacture of the HOSE ASSY, A/C, #8 . 2. APPLICABLE DOCUMENTS 2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions. 2.1.1 Documents, drawings, and publications supplied are listed under "Drawing Number". These items should be retained until an award is made. 2.1.2 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order. 2.1.3 The "Document Changes" section provides supersessions/changes to referenced documents. 2.2 Order of Precedence - In the event of a conflict between the text of this contract/purchase order and the references and/or drawings cited herein, the drawings shall take precedence. Nothing in this contract/purchase order, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. DRAWING DATA=15763 |10001| B|WS |D| | | | DRAWING DATA=56292 |53711| H|OD |D| | | | DRAWING DATA=5678032 |53711| A|DW |D| | | | 3. REQUIREMENTS 3.1 Manufacturing and Design - The HOSE ASSY, A/C, #8 furnished under this contract/purchase order shall meet the material and physical requirements as specified ; NAVSEA P/N: 5678032-501(HOSE ASSY, AC) PARTS REQUIRED WITHIN THE DRAWING ARE MANUFACTURED BY RED DOT CORP. CAGE CODE (62534) AND REQUIRE ASSEMBLY THAT MUST ADHERE TO THE REGS/SPECS WITHIN DRAWING 5678032 REV_A. RED DOT PARTS HAVE BEEN VERIFIED AS ACTIVE. ; . 3.2 Marking - Unless marking requirements are specified by a document or drawing cited in this solicitation all items delivered under this contract/purchase order shall be marked and identified in accordance with the applicable Military Standards and Specifications as follows: Mechanical Parts, Assemblies and Equipments - MIL-STD-130 Electrical and Electronic Parts - MIL-STD-1285, Method 1. Electrical and Electronic Parts and Assemblies not covered by MIL-STD-1285-use MIL-STD-130. Electronic Equipment - MIL-STD-454 Requirement Number 67. Electrical Equipment - MIL-P-15024/5 (SHIPS) 3.3 Configuration Control - MIL-STD-973 entitled "Configuration Management", Paragraph 5.4.8, Configuration Control (Short Form Procedure), is hereby incorporated. The Contractor shall submit all Engineering Change Proposals in accordance with MIL-STD-973, Paragraph 5.4.8.2 and Appendix D. Requests for Deviations shall be processed in accordance with MIL-STD-973, Paragraph 5.4.8.3 and Appendix E. Requests for Waivers shall be processed in accordance with MIL-STD-973, Paragraph 5.4.8.4 and Appendix E. (Original and two copies shall be submitted to Contracting Officer, NAVICP-MECH, P. O. Box 2020, Mechanicsburg Pa. 17055-0788.) 3.4 SHELF LIFE REQUIREMENT - The following is excerpts from DOD 4140.27-M Shelf Life Management Manual. This requirement is mandated by MIL-STD-129P and later and is required under the under the Preservation, Packing and Marking portion of this TDP. 2-12. 85 Percent SHELF-LIFE REMAINING REQUIREMENT APPLICABLE TO ACQUISITION/PROCUREMENT A. Acquisition/procurement documentation must specify that shelf-life items/material will have not less than 85 percent (allowing for rounding to whole months) of shelf-life remaining at time of receipt by the first Government activity. Any delivery from a contractor not having at least 85 percent shelf-life remaining must normally be considered non-conforming. Refer to Appendix E of this Manual to determine the amount of time that 85% equates to in terms of remaining shelf life for Type I or Type II shelf-life codes. B. In supporting imminent use or consumption, the 85% shelf-life remaining on receipt by first Government activity may be modified or adjusted as deemed prudent at the discretion of PMs and IMMs, when support alternative arrangements such as EC, PV, DVD or local purchase are effected. Use of support alternatives for shipment/delivery to storage facilities as stock will conform to the 85% rule. 2-13. CONTRACTOR MARKING. Shelf life items will be marked for identification and control. Markings, shown below the item identification data are required on all units, intermediate, and exterior packs or unpacked items, must be per MIL STD 129, MIL-STD-130, MIL STD 290 (FSC 9150 only), or FED STD 123, (references (m) through (p)) respectively, and will include the following: A. For Type I shelf life items: apply one, as appropriate; date manufactured, date cured (for elastomeric and rubber products only), date assembled, or date packed (subsistence only); and expiration date. B. For Type II shelf life items: apply one, as appropriate; date manufactured, date cured (for elastomeric and other rubber products only), date assembled, and date packed (subsistence only), and inspect/test date. C. For both Type I and Type II markings in subparagraphs A and B above: the date must be expressed by the numeric month and the last 2 digits of the calendar year; i.e., 06/95, with the day of that month being the last day. D. Different Dates on Identical Items. When two or more unit packs of identical items bear different dates of manufacture, dates of cure, dates of pack, or dates of assembly, the earliest date must be shown on the shipping container. E. For Type I drugs and biologicals: the expiration date only is required. The expiration date should be marked in accordance with FED-SPEC PPP C 186 (reference (q)). Manufacturer date must not be shown for medical items having expiration dates. F. For cure-dated items: shelf life markings on physical material are expressed by month or quarter and year designations (i.e., 11/2001,or 3Q2001). Shelf life periods end on the last day of the cited month or quarter. Appendix E SHELF LIFE CODES Required Number of Months/Quarters Remaining Upon Receipt by the first Government activity Type I Type II Months Quanters Shelf Life Period Non-Deteriorative 0 0 N/A N/A No Shelf-Life Applies (zero) (zero) 01 Month A N/A 25 DAYS N/A 02 Months B N/A 50 DAYS N/A 03 Months C 1 75 DAYS