6515--CENTRELLA MAX AIR MATTRESSES

IAW FAR 15.201(e), responses to this notice are not offers and cannot be accepted by the Government to form a binding contract. Responders are solely responsible for all expenses associated with responding to this Sources Sought Notice. SOURCES SOUGHT DESCRIPTION This is NOT a solicitation announcement. This is a Sources Sought Notice only. The purpose of this Sources Sought Notice is to gain knowledge of potential qualified sources and their size classification relative to NAICS code 339113 (size standard of 800 Employees). Responses to this Sources Sought Notice will be used by the Government to make appropriate acquisition decisions. After review of the responses to this Sources Sought Notice, a solicitation announcement may be published. Responses to this sources sought synopsis are not considered adequate responses for a solicitation announcement. The Department of Veterans Affairs (VA), VISN 02 Network Contracting Office, is seeking sources that can provide ten (10) Centrella Max Air Surf Air Surfaces or equivalent with the salient characteristics listed below: The James J. Peters VA Medical Center requires the procurement of the Centrella Max Air Surf Air Surfaces, or an equivalent product, to support specialized patient care protocols related to skin integrity, advanced pressure redistribution, and microclimate management. Salient Characteristics / Technical Requirements The Contractor shall provide commodities that meet or exceed the following explicit salient characteristics: Physical & Fit Specifications: Dimensional Alignment:� Must feature an exact 36-inch width and contour shaping designed specifically to interface with the Hillrom Centrella Smart+ Bed frame, without restricting siderail operational movement or impeding integrated frame scale readouts. Component Specificity:� Similar to Hillrom Model P7922A05 with an integrated premium top cover. Performance Specifications: Weight Profile Support:� Surface must utilize an automated weight-driven system, dynamically adjusting pressure redistribution across a weight range of 70 lbs to 500 lbs. Microclimate Control:� Must possess active, integrated blower-driven Microclimate Management technology to continuously extract moisture vapor and heat away from the patient's skin interface layer. Safety Interface Optimization:� Must feature embedded sensor technology compatible with the Centrella frame s Side-Sitting Detection and advanced Bottoming-Out Protection mechanisms, to mitigate pressure-related injury risks during patient egress. Targeted Zones:� Must provide integrated heel-slope features for advanced pressure offloading at the patient's lower extremities. Infection Control & Cleanability: Seam Integration:� Top cover must feature RF-welded or fluid-impermeable sealed seams to eliminate opportunistic fluid ingress. Disinfection Compliance:� Materials must maintain physical integrity when subjected to standardized hospital-grade disinfectants (e.g., sodium hypochlorite, quaternary ammonium compound solutions). Performance Period: Vendor must provide deliverable items within 60 days of award, unless otherwise directed by the Contracting Officer. Place of Delivery: James J. Peters VA Medical Center Warehouse 130 W. Kingsbridge Rd Bronx, NY 10468 *The VA has a preference for domestically manufactured items in the United States. The information identified above is intended to be descriptive, not restrictive and to indicate the quality of the supplies/services that will be satisfactory. It is the responsibility of the interested source to demonstrate to the government that the interested parties can provide the supplies/services that fulfill the required specifications. If you are interested and are capable of providing the sought out supplies/services, please provide the requested information as well as the information indicated below. Response to this notice should include company name, address, point of contact, size of business pursuant to the following questions: Please indicate the size status and representations of your business, such as but not limited to: Service Disabled Veteran Owned Small Business (SDVOSB), Veteran Owned Small Business (VOSB), Hubzone, Woman Owned Small Business (WOSB), Large Business, etc.)? (2) Is your company considered small under the NAICS code identified under this RFI? (3) Are you the manufacturer, distributor, or an equivalent solution to the items being referenced above? (4) If you are a large business, do you have any designated distributors? If so, please provide their company name, telephone, point of Contact and size status (if available). (5) If you re a small business and you are an authorized distributor/reseller for the items identified above or an equivalent solution, do you alter; assemble; modify; the items requested in any way? If you do, state how and what is altered; assembled; modified? (6) If you intend to sub contract any work on this contract, what portion of the total cost will be self-performed/will be performed by your organization? Please provide estimated detailed percentage breakdowns related to sub contracted work and completion of job. (7) Does your company have an FSS contract with GSA or the NAC or are you a contract holder with NASA SEWP or any other federal contract? If so, please provide the contract number. (8) If you are an FSS GSA/NAC or NASA SEWP contract holder or other federal contract holder, are the items/solution you are providing information for available on your schedule/contract? (9) General pricing of your products/solution is encouraged. Pricing will be used for the purpose of market research only. It will not be used to evaluate for any type of award. (10) Please submit your capabilities in regard to the salient characteristics being provided and any information pertaining to equal to items to establish capabilities for planning purposes? (11) Will the items you will be providing manufactured domestically in the United States or are they foreign manufactured items? (12) Please review salient characteristics/statement of work (if applicable) and provide feedback or suggestions. If none, please reply as N/A. (13) Please provide your Sam.gov Unique Entity ID number. *** Submissions addressing number (10) should show clear, compelling and convincing*** evidence that all equal to items" meet all the salient characteristics. Responses to this notice shall be submitted via email to Wilmen.Joa@va.gov telephone responses shall not be accepted. Responses must be received no later than August 14th, 2026, 11 AM EST. If a solicitation is issued it shall be announced at a later date, and all interested parties must respond to that solicitation announcement separately from the responses to this sources sought. Responses to this sources sought notice are not a request to be added to a prospective bidders list or to receive a copy of the solicitation.