LIGHT,LANDING,AIRCR

T|45 DAYS AFTER THE DEFECT WAS FOUND||||| EQUAL OPPORTUITY FOR WORKERS WITH DISABILITIES (JUN 2020)|2||| BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM-BASIC (FEB 2024)|11|||||||||||| CONTRACT TERMS AND CONDITIONS REQUIRED TO IMPLEMENT STATUTES OR EXECUTIVEORDERS--COMMERCIAL PRODUCTS AND COMMERCIAL SERVICES (MAR 2025)(DEVIATION 2025-O|81|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||| CUTIVE ORDERS--COMMERCIAL PRODUCTS AND COMMERCIAL SERVICES (MAR 2025)(DEVIATION|16||||||||||||||||| SERVICES (MAR 2025)(DEVIATION 2025-O0003 AND 2025-O0004))|3|||| ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (OCT 2024)|13|||||||||||||| BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024))|5|||||| BUY AMERICAN--BALANCE OF PAYMENTS PROGRAM (FEB 2024)|1|| ROYALTY INFORMATION (APR 1984)|1|| ANNUAL REPRESENTATIONS AND CERTIFICATIONS (MAR 2025)(DEVIATION 2025-O0003 AND 2025-O0004))|12|336320|1000||||||||||| NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PREPAREDNESS, ANDENERGY PROGRAM USE (APR 2008))|2||X| EVALUATION--COMMERCIAL PRODUCTS AND COMMERCIAL SERVICES (NOV 2021)|4||||| THE PURPOSE OF THIS AMENDMENT IS TO EXTEND THE SOLICITATION CLOSE DATE. THE PURPOSE OF THIS AMENDMENT IS TO EXTEND THE SOLICITATION CLOSE DATE. This solicitation is for the repair of a commercial item for the P8 Aircraft system. This solicitation will be using competitive procedures. The Government will issue an order resulting from this Request for Quotation to the responsible offeror whose quotation, conforming to the solicitation, results in the best value to the Government. Proposal submission should include non-price factors and price on one document. The evaluation will consider RTAT as more important than capacity. Descending order of factors. The Government reserves the right to award the contract to other than the lowest priced offer. (1) RTAT. (2) Capacity. (3) Price. (4) Past Performance. Offerors are instructed to submit Firm Fixed Prices for any quote submittal. Tiered pricing will not be accepted or evaluated. Quotes may be emailed to the following address and must be received by 04:30PMEST on the closing date, listed in block 10 on page 1 of this solicitation:casey.a.russ.civ@us.navy.mil Quotes received after the closing date are considered to be late and will not be considered for award. If only one acceptable quote is received in response to this solicitation, competitive procedures will shift to sole source negotiations. This requirement can only be repaired from Original Equipment Manufacturer (OEM), aircraft prime, or suppliers who provide Federal Aviation Administration (FAA)-Certified parts which possess an FAA Authorized ReleasedCertificate, FAA Form 8130-3 Airworthy Approval Tag from certified repairstations pursuant to 14 CFR Part 145. ALL CONTRACTUAL DOCUMENTS (I.E. CONTRACTS, PURCHASE ORDERS, TASK ORDERS, DELIVERY ORDERS AND MODIFICATIONS) RELATED TO THE INSTANT PROCUREMENT ARE CONSIDERED TO BE "ISSUED" BY THE GOVERNMENT WHEN COPIES ARE EITHER DEPOSITED IN THE MAIL, TRANSMITTED BY FACSIMILE, OR SENT BY OTHER ELECTRONIC COMMERCE METHODS, SUCH AS EMAIL. THE GOVERNMENT'S ACCEPTANCE OF THE CONTRACTOR'S PROPOSAL CONSTITUTES BILATERAL AGREEMENT TO "ISSUE" CONTRACTUAL DOCUMENTS AS DETAILED HEREIN. Early and incremental deliveries accepted. 1. The contractor shall provide notification to the government of all proposedengineering changes that effect components managed under this contract. Nochanges shall be made without written authorization from the government for any change which will or may affect: a) Interchangeability, performance, weight, safety, reliability, service life,fit, form, function, and maintainability; or b) Federal Aviation Administration (FAA) type certification c) Require part re-identification for any reason 2.The change notification shall include at a minimum the affected partsnumber(s) and a required approval date in order to maintain current contractual performance requirements. The contractor shall make available to the government any commercially available change documentation such as Service Bulletin or Original Equipment Manufacturer Product Line Change Notifications. Repair Turnaround Time (RTAT) definition: The contractual delivery requirement is measured from asset Return to the date of asset acceptance under the terms of the contract. For purposes of this section, Return is defined as physical receipt of the F-condition asset at the contractor?s facility as reflected in the Action Date entry in the Commercial Asset Visibility (CAV) system. In accordance with the CAV Statement of Work, the contractor is required to accurately report all transactions by the end of the fifth regular business day after receipt and the Action Date entered in CAV must be dated to reflect the actual date of physical receipt. The Contractor must obtain final inspection and acceptance by the Government for all assets within the RTATs established in the subsequent contract. Desired RTAT: 90 days after receipt of asset Throughput Constraint: Contractor must provide a throughput Constraint for each NSN(s). Total assets to be repaired monthly after initial delivery commences X/month. A throughput of ##____ per month reflects no throughputconstraint. Induction Expiration Date: 365 days after contract award date. Any asset received after this date in days is not authorized for repair without bi-lateral agreement between the Contractor and NAVSUP WSS Contracting Officer. Reconciliation: A reconciliation modification will be issued after final Inspection and acceptance of all assets inducted under the subsequent contract. The parties have agreed to a price (shown on the schedule page) foreach unit at the negotiated RTAT. Such prices are based on the Contractor meeting the RTAT requirements described within the schedule page. If the Contractor does not meet the applicable RTAT requirement, consideration will be assessed and subject to negotiation. For information or questions regarding this notice, please contact Casey Russat the email address: Casey.a.russ.civ@us.navy.mil. 1. SCOPE 1.1 . Markings shall be in accordance with MIL-STD-130. 1.2 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;GRIMES AEROSPACE CO; drawing number ( ;72914; ) ;72500410-4; , Revision ;Latest; and all details and specifications referenced therein. 1.3 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification. 1.4 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C. 2. APPLICABLE DOCUMENTS - NOT APPLICABLE 3. REQUIREMENTS 3.1 1.0 GENERAL 3.1.1 This Statement of Work (SOW) establishes the criteria for repair and testing /inspection of the subject item. It includes inspection, component repair and replacement,reassembly and testing