P400--Building 149 and 150 Demolition 552-26-201

essitates additional access and demolition considerations. Scope. The contractor shall supply all necessary labor, materials, equipment, and services to execute the following tasks: Demolition. Demolition of Building walls and roof system in their entirety. Utility Removal and Termination. Removal and safe termination of steam and condensate return lines in each building at their source. Removal and safe termination of electrical systems in each building at their source. Removal and safe termination of water supply in each building at their source. The contractor shall provide a detailed Utility Shutdown Plan outlining the steps and precautions for safely shutting down, de-energizing, and terminating all utilities for these two buildings. Retention of Structural Elements. The concrete floor of each building is to be protected and preserved. Sidewalks adjacent to both buildings are to be protected and preserved. Tunnels with concrete lids are to be protected and preserved. Temporary Fencing. Installation and maintenance of temporary fencing around the entire perimeter of the demolition sites for both Building 149 and Building 150 for the duration of the project . Fencing must be a minimum of six (6) feet high and secured to prevent unauthorized access. Clearly marked construction site signs to be placed on the fencing to indicate restricted access and necessary safety precautions. Construction Waste Documentation. The contractor shall document all construction waste generated during the demolition process. Provide documentation to the COR detailing the types and quantities of construction waste, including disposal methods and locations. Daily Logs. The contractor shall maintain and submit daily logs of all activities on the site. Daily Logs should include details of work performed, personnel on-site, equipment used, any safety incidents or near misses, and any other relevant information. Daily logs should be submitted to the Contracting Officer's Representative by the end of each work week. Performance Monitoring. The Contracting Officer or their Representative will perform inspections to verify compliance with the SOW. Security Requirements. The C&A requirements do not apply, and a Security Accreditation Package is not required. Security Badges. All contractor personnel must be issued and visibly wear security badges at all times while on-site. Security badges must include the contractor's name and photo identification. Procedures for obtaining and returning security badges must be coordinated with the Contracting Officer's Representative. Safety and Compliance. Demolition activities must strictly comply with all applicable federal, state, and local regulations, ensuring adherence to the highest safety and environmental standards. This includes, but is not limited to: Occupational Safety and Health Administration (OSHA) Standards. OSHA 29 CFR 1926 Subpart T - Demolition, which outlines general safety and health provisions specific to demolition activities. OSHA 29 CFR 1910.147 - The control of hazardous energy (lockout/tagout) to prevent accidental startup of machinery and the release of hazardous energy. OSHA 29 CFR 1926 Subpart E - Personal Protective and Life Saving Equipment, ensuring all workers are equipped with the necessary safety gear. Environmental Protection Agency (EPA) Regulations. Compliance with the Clean Water Act (CWA) for managing water runoff and discharges. Adherence to the Clean Air Act (CAA) for controlling dust and emissions, particularly the National Emission Standards for Hazardous Air Pollutants (NESHAP) regarding asbestos. Master Specification. Specification 02 41 00 Demolition Specification 01 35 26 Safety Requirements for Major Projects State and Local Regulations. Obtain all necessary permits from state and local authorities, including demolition permits and waste disposal permits. Adherence to state-specific occupational safety regulations and environmental protection guidelines. National Fire Protection Association (NFPA) Standards. NFPA 70 (National Electrical Code) for ensuring all electrical disconnections are performed safely. NFPA 241 for safeguarding construction, alteration, and demolition operations. Hazardous Material Handling. Compliance with the Resource Conservation and Recovery Act (RCRA) for the management and disposal of hazardous waste. Adherence to Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) for any potential hazardous substance releases and required reporting. All activities must be conducted under the supervision of qualified and certified personnel, ensuring complete adherence to these standards and regulations. Detailed records of compliance shall be maintained and available for review upon request. The contractor shall implement a site-specific safety plan addressing all potential hazards, including the safe removal of materials of unknown type and quantity buried under the roof debris. Utility Termination. The contractor shall verify, ensure, and coordinate the proper disconnection and termination of all utility lines, including steam, water, and electricity associated with these two buildings. This involves collaborating with relevant utility providers, conducting thorough inspections to confirm disconnections, and implementing safety protocols to prevent any accidental utility service disruptions or hazards during the demolition process. The contractor shall obtain all necessary permits and approvals required for the termination of utility services. This includes coordinating activities with Engineering and effected services, submitting detailed shop drawings and documentation, and ensuring compliance with all relevant regulations and codes for the safe disconnection of utilities such as water, electricity, and steam lines. The contractor is strictly prohibited from performing any electrical hot work under any circumstances. Prior to commencing any demolition or construction activities, all electrical systems must be completely de-energized. This process includes isolating and shutting down power sources, locking out and tagging out all electrical circuits in accordance with OSHA Standard 29 CFR 1910.147 for the control of hazardous energy, and thoroughly verifying that the area is safe to work in through proper testing and inspection procedures as outlined in NFPA 70E. Additionally, the contractor must maintain documentation confirming that these safety measures have been implemented and adhered to, including compliance with the National Electrical Code (NEC) and other relevant federal, state, and local regulations. The contractor is required to provide a comprehensive Utility Shutdown Plan that outlines the specific steps and precautions for safely shutting down, de-energizing, and terminating all utility services. This plan must adhere to all relevant regulations and standards, including but not limited to OSHA Standard 29 CFR 1910.147, which covers the control of hazardous energy (lockout/tagout) procedures, and NFPA 70E for electrical safety in the workplace. The plan should include: Identification and assessment of all utility lines, including electricity, water, steam, gas, and any other services. Detailed procedures for isolating and shutting down power sources in compliance with OSHA lockout/tagout requirements. Verification processes to ensure complete de-ener