ACTUATOR,ELECTRO-ME

@dla.mil | BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM-BASIC (FEB 2024)|11|||||||||||| NOTICE OF CYBERSECURITY MATURITY MODEL CERTIFICATION LEVEL REQUIREMENTS (NOV 2025))|1|| SMALL BUSINESS SUBCONTRACTING PLAN (DOD CONTRACTS)-BASIC (DEV 2026-O0037)(FEB 2026))|2||| SECURITY PROHIBITIONS AND EXCLUSIONS (CLASS DEVIATION 2026-O0025)(FEB 2026)|7|||||||| SMALL BUSINESS PROGRAM REPRESENTATIONS (DEV 2026-O0037)(FEB 2026)|20|335999 |600||||||||||||||||||| BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024))|5|||||| BUY AMERICAN-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024)|1|| ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (DEVIATION 2026-O0043)(FEB 2026))|13|||||||||||||| QUANTITY HAS INCREASED FROM 8 EACH TO 9 EACH. TECHNICAL DATA PACKAGE HAS BEEN HEREBY UPDATED. \ This Soliciation is being issued under Special Emergency Procurement Activity (SEPA) - Emergency Acquisition Flexibilities (EAF) authority. FMS QUOTES CAN BE SUBMITTED IN HARDCOPY FORM. A COMPLETED COPY OF THE SOLICITATION, CAN BE SUBMITTED TO THE CONTRACTS OFFICE BY POSTAL MAIL OR ATTACHED TO EMAIL MARCHAUNDA.TILLER@DLA.MIL BY THE CLOSING TIME AND DATE. PLEASE PROVIDE AN EMAIL ADDRESS FOR FOLLOW UP COMMUNICATIONS. VERIFY NOMENCLATURE, PART NUMBER, AND NSN PRIOR TO REPONSDING. IUID 252.211-7003 is not required. VENDOR ( ) IS SUBMITTING THIS QUOTE AS A: M MANUFACTURER ____ DISTRIBUTOR/DEALER ____ NOTE TO DISTRIBUTORS/DEALERS: IF YOU ARE A DISTRIBUTOR, YOUR QUOTATION MUST BE ACCOMPANIED WITH A LETTER FROM THE ACTUAL MANUFACTURER INDICATING THAT YOU ARE AN "AUTHORIZED" DISTRIBUTOR. WHEN SUBMITTING QUOTES VIA EDI, MAKE SURE YOU SPECIFY ANY EXCEPTIONS (I.E. MILSPECS/STANDARDS, PACKAGING, I&A, PACKAGING HOUSES, ETC.) OR FOLLOW UP WITH AHARD COPY OF THE EXCEPTIONS. IF NOTHING IS INDICATED OR RECEIVED, AWARD WILL BE BASED UPON SOLICITATION REQUIREMENTS PART NUMBER BEING QUOTED_______________ (THIS IS THE PART NUMBER THAT WILL BECALLED OUT ON THE ORDER. IF DIFFERENT THANTHE ONE SHOWN ON SOLICITATION,PROOF OF BEING IAW P/N REQUESTED MUST BE SUBMITTED WITH QUOTE. IF AFTER AWARD, ANY CHANGE REQUESTS FOR THE P/N QUOTED AND MODIFICATION NEEDED,CONSIDERATION COSTS SHALL BE TAKEN FOR THE CHANGE. SURPLUS MATERIAL __ Surplus not preferred. If surplus is the only option, it must be new surplus Ensure you submit all the documentation to the Country Manager so they can share with the customer. When surplus is considered, follow procedures under Defense Logistics Acquisition Directive (DLAD) 11.302 and 11.390, including the use of DLAD Procurement Note C04. In cases where acceptable surplus is restricted, be sure to include the justifiable reason with specificity (i.e. limitation by DLAD 9.202, etc.). Refurbished not allowed under most circumstances. NOTICE TO SURPLUS/NEW SURPLUS/NEW MANUFACTURED SURPLUS SUPPLIERS: A SURPLUS MATERIAL CERTIFICATE MUST ACCOMPANY ALL QUOTES FOR SURPLUS/NEW SURPLUS/NEWLY MANUFACTURED SURPLUS MATERIAL. IF SUBMITTING A QUOTE VIA EDI, A COPY OF THIS CERTIFICATION CAN BE SENT TO THE BUYER VIA FAX OR EMAIL. CoC (Certificate of Conformance) authorized when determined appropriate by the Contracting Officer. ALL FREIGHT IS FOB ORIGIN. Military Standard Packaging required. Traceability required. T Traceability required. DESIRED DELIVERY IS 90 DAYS ADC. PLEASE PROVIDE PROPOSED DELIVERY: PROPOSED DELIVERY IS ______ DAYS ADC. Inspection and acceptance (I/A) at source is REQUIRED. Inspection and acceptance at destination is not authorized and will NOT be accepted!!!! Manufacturer CAGE: Packaging CAGE: If SUPPLIES WILL BE PACKED AT A LOCATION DIFFERENT FROM THE OFFEROR ADDRESS, THE OFFEROR SHALL PROVIDE THE NAME AND STREET ADDRESS OF THE PACKAGING FACILITY. INSPECTION OF MATERIAL WILL BE AT: ______________________________________________________________ INSPECTION OF PACKAGING AND FINAL ACCEPTANCE OF MATERIAL WILL BE AT: 1. SCOPE 1.1 This contract/purchase order contains the requirements for manufacture and the contract quality requirements for the POWER SUPPLY ASSEMB , part of the ;MK 41 VERTICAL LAUNCHING SYSTEM; . 1.2 Master Phototools (Artwork) - the government cannot provide the Stable Base Master Phototools (Artwork). The contractor is required to acquire or develop the Stable Base Master Phototools (Artwork) for manufacture of the POWER SUPPLY ASSEMB . 2. APPLICABLE DOCUMENTS 2.1 Applicable Documents - The document(s) listed below form a part of this contract/purchase order including modifications or exclusions. 2.1.1 "Document References" listed below must be obtained by the Contractor. Ordering information is included as an attachment to this contract/purchase order. 2.2 Order of Precedence - In the event of a conflict between the text of this contract/purchase order and the references and/or drawings cited herein, the text of this contract/purchase order shall take precedence. Nothing in this contract/purchase order, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. DOCUMENT REF DATA=MIL-STD-130 | | |K |000115|A| | | DOCUMENT REF DATA=MIL-STD-1686 | | |C |951025|A| | | DOCUMENT REF DATA=MIL-STD-2000 | | |A |950607|A| | | 3. REQUIREMENTS 3.1 Manufacturing and Design - The POWER SUPPLY ASSEMB furnished under this contract/purchase order shall meet the material and physical requirements as specified ;53711 5598201-39 ; . 3.2 Marking - This item shall be physically identified in accordance with MIL-STD-130. 3.3 Soldering - Soldering shall conform to the requirements of MIL-STD-2000. 3.4 Changes in Design, Material Servicing, or Part Number - Except for a Code 1 change, which shall be processed as provided in the code statement shown below, no substitution of items shall be made until the NAVICP-MECH Contracting Officer has notified and approval has been given by issuance of a written change order. When any change in design, material, servicing or part number is made to replace or substitute any item to be furnished on this contract/purchase order, the Contractor shall furnish, for the substituting/replacement item, a drawing and an explanation of the reason for the change, explaining the reason therefor. If finished detail drawings are not available, shop drawings in the form used by the manufacturer will be acceptable for Government evaluation. When notifying the Procurement Contracting Officer of the reasons for making substitutions, the type of change shall be indicated by code number in accordance with one of the following statements: Code 1: PART NUMBER CHANGE ONLY - If the Manufacturer's Part Number indicated thereon has changed, but the parts are identical in all respects, supply the item and advise NAVICP-MECH immediately of the new part number. Code 2: Assembly (or set or kit) not furnished - Used following detail parts. Code 3: Part not furnished separately - Use assembly. Code 4: Part redesigned - Old and new parts are completely interchangeable. Code 5: Part redesigned - New part replaces old. Old part cannot replace new. Code 6: Part redesigned - Parts not interchangeable. 3.5 Vendor Waivers/Deviations - Compliance with the delivery date and technical requirements of NAVICP-MECH Repair Part Material contracts is expected. As a cautionary note, seller intended use of any material which is not in full compliance with the specified contract technical requirements sha