Pulley, Flat NSN 3020-01-664-2737

exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data. The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/Logistics-Operations/Enhanced-Validation/ To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data. JCP applies to all manufactures, dealers, distributors, or suppliers. 3. Based upon market research, the Government is not using the policies contained in Part 12, Acquisition of Commercial Items, in its solicitation for the described supplies or services. However, interested persons may identify to the contracting officer their interest and capability to satisfy the Government's requirement with a commercial item within 15 days of this notice. 8. The solicitation will contain a contractor first article test requirement that will be required unless documentation is provided showing completion of a first article test on this NSN within the past 3 years. Material receipt inspection at the contractors facility will be required due to the critical nature of the item. A Production Test & Inspection report as well as a Certificate of Quality Compliance will be required. The solicitation/contract shall contain the NAWCADLKE inspection surveillance clause as follows: a. Because of the critical nature of this material, a representative of the Naval Air Warfare Center Aircraft Division Lakehurst (NAWCADLKE) is available to furnish technical assistance on Quality Assurance (QA) matters and shall have the option of conducting QA surveillance for the first lot produced under this contract (and all subsequent lots if necessary). This requirement will be performed in conjunction with the government QAS of the cognizant Defense Contract Management Activity and does not abrogate the authority or responsibility of the designated government QAS. The contractor agrees to notify, in writing, the supervisor of the NAWC QA section Code, BL41600, Lakehurst, NJ 08733-5035 and the PCO when the material is scheduled to be presented to the DCMA government QAS for Government inspection and acceptance. This notice shall afford the NAWCADLKE QA representative the option of being present during the inspection. Notification to NAWC may be provided via telephone (732)-323-2834 immediately followed by written confirmation, or via email to Roy.a.janney.civ@us.navy.mil. A minimum of fourteen (14) working days is required to arrange the surveillance visit. Notification shall include the following information: Company Name, Cage Code, Phone number, Fax number, Contract number, Point of Contact, Part Nomenclature, Part Number, NIIN, Type of Inspection, and Quantity of parts. b. Due to the critical nature of this item, it is necessary to conduct in-process inspections on critical component features, attributes, or manufacturing processes. The contractor agrees to notify, in writing, the supervisor of the NAWC QA section Code, BL41600, Lakehurst, NJ 08733-5035 and the PCO when material is scheduled for the interim inspection(s) that are identified herein. This notice shall afford the NAWCADLKE QA representative the option of being present during the inspection. Notification to NAWC may be provided via telephone (732)-323- 2834 immediately followed by written confirmation, or via email to Roy.a.janney.civ@us.navy.mil. A minimum of seven (7) working days is required to arrange the surveillance visit. Notification shall include the following information: Company Name, Cage Code, Phone number, Fax number, Contract number, Point of Contact, Part Nomenclature, Part Number, NIIN, Type of Inspection, and Quantity of parts. Interim Inspection Requirements: The following item(s) requires an Interim Inspection at the contractor�s location: a. P/N 627240-1, Sheave Assy-Coined (CSI): i. Witness of penetrant inspection per Note 3 of Drawing 627240. ii. Verification of coining method per Note 6 of Drawing 627240 (C2). iii. Witness of post-coining inspection per Note 7 of Drawing 627240 (C3). iv. Witness of bearing shrink-fit per Note 9 of Drawing 627240 (C1). v. Witness of dimensional inspection of Drawing 627240 (M101-M104). P/N 626846-1, Bearing (CSI): i. Verification of eccentricity per Note 1.B of Drawing 626846 (M106). ii. Verification of heat treatment per Note 1.H of Drawing 626846 (M107). iii. Witness of hardness testing per Note 1.H of Drawing 626846 (M107). iv. Verification of material properties per Note 1.J of Drawing 626846 (M109). v. Verification of roller diameter per Note 1.K of Drawing 626846 (M110). vi. Witness of magnetic particle inspection per Note 5 of Drawing 626846 (M105). vii. Witness of diametral clearance prior to mounting per Note 6 of Drawing 626846 (C1). viii.Witness of dimensional inspection per Drawing 626846 (M101-M104, M108). The contractor shall assist on the conduct of the interim inspection(s) as described herein. The contractor shall provide adequate facilities, inspection equipment, and skilled personnel, to support the NAWCADLKE Inspector in the conduct of the interim inspection(s). The contractor shall provide gauges, tools, fixtures, and jigs necessary to perform the inspections. The contractor shall also provide sufficient rigging/material handling services and manpower to setup/configure/operate equipment & machines used to accomplish the inspection task. This contractor assist requirement shall be applicable to 100% of the production quantities and as a minimum, include inspection of all (100%) interim inspection requirements identified above. ALRE CSI parts require certification. When certified, an ALRE part is marked with a Material Identification Code (MIC). NAWCADLKE QA will provide the MIC to DCMA if the component is source accepted, and after receipt of all associated data. Application of MIC shall be in the same methodology as the drawing note for part marking, and in same area as part marking (next to, above, or below). Receipt inspection and Certification of Sub-Components: a. P/N 626846-1 shall be certified at the time of interim inspection. Parts will be certified and marked as directed by NAWCADLKE prior to assembly. Contractor Assist and Marking as specified below applies. Receipt Inspection and Certification of the Top Assembly: a. The receipt Inspection